EK-FH1-TP-I

ORDERING CODE EK-FH1-TP-I DESCRIPTION The EK-FH1-TP-I universal I/O module from the ÆVO Series allows you to control up to 4 groups of electrical devices, such as lights and valves, or up to 2 motorized drives, such as blinds and 3-way valves, independently and in any combination you like. for this purpose, the device has outputs equipped with potential-free bistable relay contacts that guarantee that the set control status is maintained even in the event of a power failure. The device is equipped with buttons for manual control and LEDs for status indication; a button allows you to switch between automatic and manual operation. The device has an integrated KNX bus communication module and is designed for mounting on a 35 mm profile rail. Power is supplied via the KNX bus and no auxiliary power supply is required. FUNCTIONS / CHARACTERISTICS - Switching lights on and off - Control of motorized drives - Manual control via buttons on the front - Status indication of outputs via LEDs - Configuration as a normally open or normally closed switch - Outputs and channels can be set via ETS as independent or with copy function from another output or channel - Control of ON/OFF valves and three-way valves - Up to 8 logic functions (AND, OR, XOR, etc.), object comparison and arithmetic - Block and forcing function for each channel - Timing: delay in switching on and off, stair light function with warning signal - Integration into scenarios - Energy and operating hours counter configurable via bus - Meteo alarms TECHNICAL DATA Supply - Power supply 21-30 Vdc via KNX bus - Bus current draw at start-up: 54 mA @30 Vdc, 49 mA @21 Vdc - Bus current draw in stand-by: 10 mA @30 Vdc, 13 mA @21 Vdc - Bus current draw during relay movement: 32 mA @21-30 Vdc Outputs • Switching lights on and off • Control of motorized drives • Manual control via buttons on the front • Status indication of outputs via LEDs • Configuration as a normally open/closed switch • Outputs and channels can be set via ETS as independent or with copy function from another output or channel • Control of ON/OFF valves and three-way valves • Up to 8 logic functions (AND, OR, XOR, etc.), object comparison and arithmetic • Block and forcing function for each channel • Timing: delay in switching on and off, stair light function with warning signal • Integration into scenarios • Energy and operating hours counter configurable via bus • Automatic control of motorized drives for protection from direct sunlight and weather conditions (rain, wind, frost) Inputs • 4 independent digital inputs [DI] for potential-free contacts, for example, for connecting traditional switches or buttons for on/off control of appliances • 4 inputs individually configurable as analog [AI] for measuring room temperature using a passive temperature probe (NTC 10 kΩ at 25°C) to be connected to the input with the option of sending the value to the bus and thermostat functionality • 2 independent channels (2 coupled inputs), for example, for connecting double buttons to control dimmers or motorized drives • on/off control of individual and group appliances • detection of the status of signal contacts (from safety devices, alarms, etc.) • scenario recall and storage • sending values (temperature, brightness, etc.) to the bus • lock function and shift register function Environmental conditions - Operating temperature: - 5 ... + 45°C - Storage temperature: - 25 ... + 55°C - Transport temperature: - 25 ... + 70°C - Relative humidity: 95% not condensing) Other characteristics - Housing in plastic material - Mounting on 35 mm rail (according to EN 60715) - Protection degree IP20 (installed device) - Overvoltage class III (according to EN 60664-1) - Classification climatic 3K5 and mechanical 3M2 (according to EN 50491-2) - Pollution degree 2 (according to IEC 60664-1) - Mechanical lifetime (min. cycles): 3 000 000 - Electrical lifetime (min. cycles): 100000 @8A / 25000 @16 A (Vac) - Dimensions (WxHxD): 71 x 90 x 63 mm - Weight: 277 g CONFIGURATION AND COMMISSIONING A detailed description of the parameters can be found in the device's application manual. ETS5 or later versions are required for configuration and commissioning. Application program for ETS: APEKFH1TPI##.knxprod (## = version).